What are your opinions regarding How to Install a Bathtub Yourself?
Setting up a tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old tub is easily easily accessible, the task can relocate rapidly; if you need to open up a wall surface to get rid of the old bathtub and also position the brand-new tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will need a helper to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have certified yourself for the work and fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Chances are you may need an expert plumber to make tube links.
This short article will aid you mount a brand-new bathtub in your bathroom if you have currently purchased a brand-new tub and also don't need to alter the plan of your previous water supply pipes.
Your tools as well as material list ought to consist of the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather bothersome as a result of the limited gain access to that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Using the two wood boards under its feet, put the bathtub in the needed placement. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub till the level reviews level.
To mount faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Activate the water system as well as inspect all joints as well as brand-new pipework for leaks and tighten them if necessary. Load the bath tub and also check the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been made use of at least when as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the producer given backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The previous kind ought to be connected to the tap ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and the tiling, resulting in complications with moisture and possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to enable the activity experienced when the bathtub is in usage. The sealer can crack fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the market. It is suggested to fit the tiles utilizing water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report about How to Install a Bathtub through an acquaintance on another site. If you please take the time to distribute this blog if you appreciated it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
This Site